Product information

Cobaltbis (2-ethylhexanoat).

ATTENTION!

Self-igniting! Immediately soak used material in water after use and dry outdoors!
EUH208: Contains cobaltbis. May cause allergic reactions.
EUH210: Safety data sheet available on request.

1. During working time (max. 1 hour for approx. 20–25 m²) massage the oil into the wood with the single-disk machine, using white polishing fleece. Remove any excess oil from the wood surface immediately. Wipe around edges by hand.
2. Finally polish the oiled wood surface dry again using white polishing fleece. TIP: If the oil thickens while you are working and optimum polishing is no longer possible, immediately apply oil again thinly, massage in and polish dry. Working time with the oil is shorter at high temperatures or when exposed to direct sunlight. Be sure to work on only a small area at a time otherwise a regular surface appearance cannot be achieved. It is also essential to provide shade and good ventilation to avoid moisture from the windows running onto the freshly oiled floor.
3. For badly worn floors (in commercial use etc.) re-oiling should be carried out again after a period of approx. 24 hours. ATTENTION: apply oil very thinly, polish in immediately using white polishing fleece and polish dry! No excess oil should remain on the wood surface! TIP: Empty oil into a spray, spray very finely and polish dry with sheepwool pad (this applies also for treatment to mafi floors which were supplied oiled – first treatment after installation).
4. After allowing to dry for 24 hours the floor can be walked on carefully. In case of heavier use, protective covering is necessary (final hardening approx. 10–14 days). During this time the floor should not be treated with water or other cleaning agents.

On untreated wood: 1 litre for 8–10 m² (when applied twice)
For polishing: 1 litre for approx. 40–80 m²

Cobaltbis (2-ethylhexanoat), Titanium Dioxide.

ATTENTION!

Self-igniting! Immediately soak used material in water after use and dry outdoors!
H412: Harmful to aquatic organisms, with long lasting effects.
EUH208: Contains 2-butanone oxime; cobaltbis. May cause allergic reactions.
P501: Dispose of contents/container to industrial incinerator.
P273: Avoid release into the environment.

1. During working time (max. 1 hour for approx. 20–25 m²) massage the oil into the wood with the single-disk machine, using white polishing fleece. Remove any excess oil from the wood surface immediately. Wipe around edges by hand.
2. Finally polish the oiled wood surface dry again using white polishing fleece. TIP: If the oil thickens while you are working and optimum polishing is no longer possible, immediately apply oil again thinly, massage in and polish dry. Working time with the oil is shorter at high temperatures or when exposed to direct sunlight. Be sure to work on only a small area at a time otherwise a regular surface appearance cannot be achieved. It is also essential to provide shade and good ventilation to avoid moisture from the windows running onto the freshly oiled floor.
3. For badly worn floors (in commercial use etc.) re-oiling should be carried out again after a period of approx. 24 hours. ATTENTION: apply oil very thinly, polish in immediately using white polishing fleece and polish dry! No excess oil should remain on the wood surface! TIP: Empty oil into a spray, spray very finely and polish dry with sheepwool pad (this applies also for treatment to mafi floors which were supplied oiled – first treatment after installation).
4. After allowing to dry for 24 hours the floor can be walked on carefully. In case of heavier use, protective covering is necessary (final hardening approx. 10–14 days). During this time the floor should not be treated with water or other cleaning agents.

On untreated wood: 1 litre for 8–10 m² (when applied twice)
For polishing: 1 litre for approx. 40–80 m²

Sodium hydroxide

H314: Causes severe skin burns and eye damage.
P101: If medical advice is needed, have container or label at hand.
P102: Keep out of the reach of children.
P260: Do not breathe dust/fume/gas/mist/vapor/aerosol.
P264: Wash hands thoroughly after handling.
P280: Wear protective gloves/protective clothing/eye protection/face protection/hearing protection/....
P301+P330+P331: IF INFECTED: Rinse out mouth. DO NOT induce vomiting.
P303+P361+P353: IF IN CONTACT WITH SKIN (or hair): Remove all contaminated clothing immediately. Wash skin with water [or shower].
P363: Wash contaminated clothing before wearing again.
P310: Wash contaminated clothing before wearing again.
P405: Keep under lock and key.

ATTENTION: It is essential to test before treating the actual surface.

1. Apply generously and evenly using a lye-resistant roller lengthwise along the plank. Avoid drips!
2. After allowing to dry for approx. 3–4 hours at a room temperature of approx. 20° C, oiling can be carried out using mafi Wood Floor Oil or mafi Prof Oil.

INFO: After application of the lye, the individual planks change in color shade due to the different resin content of the woods. Through UV exposure and care with the mafi wood floor soap, the entire surface appearance becomes more uniform again after approx. 6 months from installation.

1 litre for approx. 5–8 m²

Sodium hydroxide; caustic soda calcium oxide, white Pigments

H314: Causes severe skin burns and eye damage.
P101: If medical advice is needed, have container or label at hand.
P102: Keep out of the reach of children.
P260: Do not breathe dust/fume/gas/mist/vapor/aerosol.
P280: Wear protective gloves/protective clothing/eye protection/face protection/hearing protection/....
P301+P330+P331: IF INFECTED: Rinse out mouth. DO NOT induce vomiting.
P303+P361+P353: IF IN CONTACT WITH SKIN (or hair): Remove all contaminated clothing immediately. Wash skin with water [or shower].
P363: Wash contaminated clothing before wearing again.
P304+P340: IF INHALED: Remove the affected person to fresh air and ensure unobstructed breathing.
P310: Immediately call POISON CENTER/physician.
P321: Special treatment:
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove any contact lenses if possible. Continue to rinse.
P405: Keep under lock and key.

ATTENTION: It is essential to test before treating the actual surface.

1. To ensure uniform work on the floor surface, shake container well and empty into a lyeresistant pan.
2. Apply generously and evenly using a lye-resistant roller lengthwise along the plank. Avoid drips! Stir the lye occasionally while working. Pay attention that pigmentation is uniform!
3. After allowing to dry for approx. 3–4 hours at a room temperature of approx. 20° C, oiling can be carried out using mafi Wood Floor Oil white or mafi Prof Oil white.
4. To achieve a uniform surface, it is essential to massage the oil into the wood using white polishing fleece.

INFO: After application of the lye, the individual planks change in color shade due to the different resin content of the woods. Through UV exposure and care with the mafi wood floor soap, the entire surface appearance becomes more uniform again after approx. 6 months from installation.

1 litre for approx. 5–8 m²

Alcohols, ethoxylated coconut fatty acids.ph = 9,5–9,7

H318: Causes serious eye damage.
P280: Wear protective gloves/protective clothing/eye protection/face protection/hearing protection/....
pflege_sicherheitsdatenblatt_spezialreiniger_en_special-cleaner.pdfP305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove any contact lenses if possible. Continue to rinse.

1. Mix approx. ¹/₂ litre Super Cleaner with 10 litre warm water.
2. Apply wet using mop (or similar), leave to soak in for a short time and then treat the soiled surface using white polishing fleece (by hand or machine). IMPORTANT: Always treat only small areas, max. 10–15 m², at a time. Remove the solution containing the dirt immediately with clear water (always work with two buck ets!).
3. Repeat this procedure if necessary.
4. Wipe again with clear water; no Super Cleaner solution should be left on the wood sur face.
5. After the wood surface has been allowed to dry out completely, re-oiling must be carried out using mafi Wood Floor Oil or mafi Professional Oil.

Approx. 20–50 m² (depending on soiling)